Air Suspension Compressor Pump For Ford Expedition Lincoln Navigator with Dryer. 1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number). 01 37106781843 Pneumatic Spring, Rear 02 37221092403 Threaded Joint 03 37206864215 Gas Supply Device 03 37206875176 Gas Supply Unit 03 61368373700 Relay Switch Weissgr 05 37206850595 Ventilation Pipeline 05 37206874510 Ventilation Pipeline 06 37206793277 Left Intake Pipe 07 37206793278 Right Intake Pipe 08 34306784201 Conductor Clamp Double 09 07130519991 Positioning Block 10 34326855500 Brake Pipeline Of Bracket 11 64111364073 Conductor Bracket 12 61359271313 Device Insertion Under Components 13 37146860385 Air Spring Control Unit 14 61131383776 Plug Contact Mqs 14 61136913626 Universal Plug Shell No Code 14 61136913644 Decoration Cover. Air Suspension Compressor Assembly Removal. Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery. Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur. Set the steering to straight ahead. Remove protective shroud from under the rear of the vehicle to access the compressor.Disconnect the three(3)electrical connectors from the valve block and compressor assembly. Disconnect the rubber intake hose. Disconnect the red and blue air lines from the valve block(note:Black line does not have to be disconnected). Remove the four(4)outer mounting nuts that secure the compressor bracket assembly to the vehicle. Remove the entire compressor assembly from the vehicle.
Remove the air line from the compressor. Remove the air line fitting from the air hose by sliding the threaded portion up the line and spreading the collet open. Slide the air fitting off the air line. Remove the three(3)torx screws that secure the mounting bracket to the compressor.Air Suspension Compressor Assembly Installation. Install the air compressor assembly into the vehicle using the factory mounting hardware. Remove plug and insert intake hose. Reattach the red(upper)and blue(lower)air lines.
Reconnect all three(3)electrical plugs and clip the power plug into the bracket. Replace the protective shroud over the compressor. When the air compressor being replaced, the matching relay must be replaced according to the corresponding vehicle. If there is something wrong with the relay which leads the compressor to continuous operation without any break, it will burn out the electric motor or other plastic part.When the air compressor being installed, the critical parts such as rubber shock pad and damping spring must be fully fixed on the stand without short installation or missing installation (The air compressor is unequipped with parts). With the anti-vibration parts of short installation or missing installation, a loud noisy instance will happen when the air compressor is working for the sake of resonance. Distribution valve, shock absorber, air tank and tube connector must be checked after air compressor installed to ensure air-tightness. The lifespan of the air compressor will be shortened if the leakage exists.
Increased noises while the compressor is running may be caused by a non-functioning compressor mounting. Change the rubbers and springs of the mounting in any case.A porous intake hose often is the cause for a breakdown of the compressor. Change the intake hose and preferably also the filter and noise absorber, because we do not want the compressor to breakdown because of these. Change the relays before installing the compressor even if it seems to still work.
Be sure to change the right relays. Relays look similar, that is why there is a risk to change the wrong relays. Be sure to check whether the system is leakproof after repairing.The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature. Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes. On the day after measure these heights again and compare them with the ones before. Even a small difference will lead to a damaged compressor and damaged valves in the long run. Single Dimension(CM) 35.00(length)22.00(width)22.00(height). Front Engine RWD & 4WD. International Buyers C Please Note. These charges are the buyers responsibility.
Q: How do I return an item? Please contact our customer service before you return an item. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers. If you are satisfied with the product you received, wish you can leave us a feedback. Lift 3" Front & 2" Rear Leveling Kit Fits Toyota Tacoma 4Runner FJ Cruiser 4WD.
UTV & ATV Brake System Parts. Nerf Bars & Running Boards.Wheel Stem Air Valve Cap. Splash Guards & Mud Flaps. 4 pcs wheel hub bearing. Car Window Film Tint Tools. 2pc 3157 4114 4157 LED DRL Driving Daytime Running Light Bulbs 12SMD 6000K White. Fuel Pump for Chevy S10 GMC Sonoma Hombre 4.3L 97-02 for Isuzu Hombre 4.3L 97-20. 12V Universal Fuel Pump Gas Diesel Inline Low Pressure HEP-02A BHEP-02A. Turbo Turbocharger For Chevy Cruze Sonic Trax & Buick Encore 1.4T. The item "Air Suspension Compressor Pump For Ford Expedition Lincoln Navigator with Dryer" is in sale since Wednesday, July 28, 2021.
This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Suspension & Steering\Shocks & Struts". The seller is "cn-batteries" and is located in Ontario, California.This item can be shipped worldwide.